Controleur pour imprimante 3D (Marlin)

Controleur pour imprimante 3D (Marlin)


3D printer without drive board MKS GEN L V1.0 motherboard control board compatible with RAMPS open source marlin

Product parameters
Product Name: MK8 Extruder Block
Product material: pure aluminum alloy
Surface treatment: oxidation sandblasting
Product color: red
Product features: Optimized design, uniform foundation, flexible, adjustable
 
product manual
1. Please re-check whether the positive or negative is reversed before power on, if it is due to the user's connection to the power supply and burn out.
We do not guarantee this type of problem!
2. Please don't insert or pull the motor and driver under the condition of power, it will cause the driver to burn out;
Adjust the current during operation of the motor. The right way is to disconnect the power, remove the motor, and then
Re-power on, adjust the potentiometer, and measure the voltage on the potentiometer until the measured voltage is the same as expected. Do not insert the reverse drive, otherwise it will burn out the drive, or even burn the motherboard! Do not include the motor drive, the motor drive, please purchase. When the power is reversed, the motor drive board will be reversed
The chip and circuit can be burned. Please recheck and reenergize. Owner reminder:
1. MKS Gen-L V1.0 is an open source host for Ramps 1. 4, Megatronics V2.0, etc.
Problems with the board, especially optimized to develop a product, especially suitable for mass production of 3D
The manufacturer of the printer is used as a master control board.
2, fully consider the stability, heat dissipation, ease of use issues, after a continuous print reliability test. 3, if special needs can contact the owner to discuss.
4, supporting line can refer to: 2PIN, 3PIN, 4PIN
Product advantages
1, the 2560 and ramps1.4 gathered on a board to solve the Ramps 1. 4 combination
The problem of cumbersome and prone to failure.
2, the user can replace the motor drive, support 4988 drive and 8825 drive, TMC2100
Drive.
3, set an external drive signal, external drive can be connected to drive the 57,86 motor.
4, the use of high-quality MOSFET tube, better heat dissipation, to ensure long-term stability.
5, using a dedicated power chip, support 12V-24V power input, solve the Ramps voltage conversion
Chip fever, insufficient power supply.
6, stable and reliable filter circuit greatly reduces the possibility of interference, the maximum possible to avoid printing
In the course of the crash, running around and so on.
7, using CH340 serial chip, to ensure the stability and reliability under the premise of reducing costs, it is the solution
Resolved the past 16U2 difficult to drive the problem.
8, can accept 24V input, the same system power can reduce the hot bed current to 1/4, effective
Solve hot bed MOS tube heating problem.
9, the use of open source firmware Marlin, configuration and ramps1. 4 exactly the same, can be directly replaced
Ramps1.4.
10, can directly connect 2004LCD display and 12864L CD display, supportable
TFT28, TFT32 touch screen.
11, XYZ axis uses different colors of the terminal to correspond to the motor and limit switch, convenient wiring. 12, humanized design, use different colors of the terminal to distinguish the driving direction, reduce the probability of insertion,
Prevent damage to the motherboard due to drive plugs.

Product parameters
Name: 3D Printer Control Board MKS Gen-L V1.0
Include:
MKS Gen-L V1.0 Main Board*1
USB cable*1
Ancillary products, not included, need to be purchased separately:
4 (two-head 5) stepper motors: 42 motor with line limit switches 3: MKS limit switches
Motor Drive 4: 4988 or 8825 or 8729, TMC2100
Display 1 : 2004 or 12864 hot bed 1 : MK3
Hot Bed Thermometry 1 Set: Thermometer Set

Écrire une critique

Remarque: HTML n`est pas traduit!
    Mal           Bien
Captcha
  • : 262
  • Code produit: MKSGENLV1.0
  • Disponibilité: En stock
  • $29.95